Best revolver grips
A revolver grip sets concealment, recoil comfort and trigger reach at once. Start with the frame, then decide between a boot grip and a full grip.
Revolver grips are frame-specific. A grip for a Smith & Wesson J-frame will not fit a K-frame, and Ruger’s double-action revolvers use a different mounting system again. Once you know the frame, the main decision is size: a short boot grip that hides well, or a full grip that gives every finger a place and spreads recoil.
Quick picks
| Pick | Grip | Why |
|---|---|---|
| Top pick | Hogue Monogrip | Soft, one-piece and available for nearly every common frame. |
| Pocket carry | Hogue Bantam Boot Grip | A boot grip that ends flush with the frame. |
| Hard recoil | Pachmayr Diamond Pro Grip | Rubber over the backstrap to cushion the web of the hand. |
| Wood | Altamont Wood and Laminate Revolver Grips | Classic looks, including boot and combat shapes. |
| G10 | VZ Grips G10 Revolver Grips | Slim, tough and textured. |
How to choose
Identify the frame
Smith & Wesson uses letter sizes: J is the small five-shot frame, K and L are medium and share a grip size in current round-butt guns, and N is large. Ruger’s LCR, SP101 and GP100 each take their own grips. See revolver frame sizes.
Round butt or square butt
Current Smith & Wesson production is mostly round butt. Older guns may be square butt. Conversion grips let a round-butt frame wear a square-butt shape, but not the reverse.
Boot grip or full grip
Boot grips leave the little finger off and print less. Full grips are easier to shoot well, especially with magnum loads.
Open or covered backstrap
A grip that covers the backstrap puts rubber between your hand and the frame and lengthens trigger reach slightly. An open backstrap keeps reach short for smaller hands.
The grips
Monogrip
Best for general range and field use
- Type
- One-piece revolver grip
- Material
- Molded rubber
- Texture
- Cobblestone
- Traction
- Mild
- Adds
- Finger grooves, palm swell
- Install
- Slides on from below, one screw
- Price tier
- Budget
The Monogrip is a single molding with no seam down the backstrap. It slides onto the frame from below and locks with one screw into a stirrup. Finger grooves, a palm swell and Hogue’s Cobblestone texture are standard. Hogue makes it for Smith & Wesson, Ruger, Taurus and Colt frames, and Ruger ships it on many GP100s.
Trade-off. Bulky for concealment, and the grooves fix where your fingers sit.
Bantam Boot Grip
Best for pocket and ankle carry
- Type
- Boot grip
- Material
- Molded rubber
- Texture
- Cobblestone
- Traction
- Mild
- Adds
- Minimal, ends at the frame
- Install
- Snaps over the frame
- Price tier
- Budget
The Bantam is Hogue’s smallest grip. It follows the outline of the frame and stops at the bottom of the butt, with shallow finger grooves at the front. It fits by gripping the frame rather than using a conventional screw.
Trade-off. Two-finger hold, so recoil with hot loads is sharper.
Diamond Pro Grip
Best for magnum recoil
- Type
- One-piece revolver grip
- Material
- Checkered rubber
- Texture
- Checkered
- Traction
- Medium
- Adds
- Finger grooves, covered backstrap on some models
- Install
- One screw
- Price tier
- Budget
The Diamond Pro is the current version of Pachmayr’s rubber revolver grips, with a checkered diamond texture and finger grooves. Some versions cover the backstrap to pad the web of the hand. Pachmayr’s Gripper, Compac and Presentation grips remain available for people who prefer those shapes.
Trade-off. A covered backstrap lengthens trigger reach, which is a drawback for short fingers.
Wood and Laminate Revolver Grips
Best for a traditional or dress revolver
- Type
- Two-piece revolver grips
- Material
- Hardwood or wood laminate
- Texture
- Wood grain
- Traction
- Mild
- Adds
- Boot, combat and target shapes
- Install
- One screw
- Price tier
- Mid-range
Altamont offers checkered and smooth wood grips in boot, combat and target shapes for common Smith & Wesson and Ruger frames, including panel inserts for Ruger’s rubber factory grips.
Trade-off. Wood does nothing to absorb recoil.
G10 Revolver Grips
Best for a thin, durable carry grip
- Type
- Two-piece revolver grips
- Material
- G10 laminate
- Texture
- Checkered
- Traction
- Aggressive
- Adds
- Slim, boot or full length
- Install
- One screw
- Price tier
- Premium
VZ machines G10 grips for J, K and L frames and some Rugers. They are slimmer than rubber, which helps speedloaders clear and makes the gun easier to hide, and the texture does not wear.
Trade-off. Hard and thin, so they pass recoil straight to the hand.
Questions people ask
Are K-frame and L-frame grips the same?
In current Smith & Wesson round-butt revolvers, K and L frames share a grip size, so grips are sold as K/L round butt. Older square-butt guns need square-butt grips.
Why do some grips interfere with speedloaders?
Thick left panels can block a speedloader from lining up with the cylinder. Grips described as speedloader compatible have a relief cut on the left side.
Do Ruger GP100 grips fit the SP101?
No. Both use Ruger’s peg-style grip frame, but they are different sizes.